top bar

Difference between revisions of "PgFocus"

(Created page with "pgFocus is an open source and open hardware focus stabilization device developed by Karl Bellvé at the Biomedical Imaging Group (PMM, University of Massachusetts Medical School)...")
 
Line 1: Line 1:
 +
== Description ==
 +
 
pgFocus is an open source and open hardware focus stabilization device developed by Karl Bellvé at the Biomedical Imaging Group (PMM, University of Massachusetts Medical School).
 
pgFocus is an open source and open hardware focus stabilization device developed by Karl Bellvé at the Biomedical Imaging Group (PMM, University of Massachusetts Medical School).
  
 
The pg in pgFocus is short for "Pretty Good". pgFocus isn't "Perfect", or "Definite" but it is pretty good!
 
The pg in pgFocus is short for "Pretty Good". pgFocus isn't "Perfect", or "Definite" but it is pretty good!
  
pgFocus is designed to track and control focus within ±3nM at 30Hz under optimal conditions.  
+
== Hardware ==
 +
 
 +
pgFocus uses the same [http://www.atmel.com/devices/ATMEGA32U4.aspx Atmel ATMEGA 32U4] seen in the [http://arduino.cc/en/Main/arduinoBoardLeonardo Arduino Leonardo].
 +
 
 +
== Software ==
 +
 
 +
After the Leonardo was released, pgFocus was redesigned to take advantage of the bootloader for the Arduino Leonardo. If you can write an Arduino sketch, you can modify the source code to pgFocus!
 +
 
 +
 
 +
== Optics ==
 +
 
 +
pgFocus uses a laser beam that is total internally reflected off the cover glass/water interface to monitor the microscope focus. Hence, an objective with an NA of at least 1.45 is required.
 +
The laser beam wavelength should be different from that being used for science (808nm is a good choice) and must be coaligned with the TIRF beam. This can be done using a mirror, beam splitter and a short pass filter. Care must be taken to ensure that the fluorescence filter cube and other microscope optics will allow the return of the pgFocus beam back along its input path and back to the pgFocus detector and that the microscope optics will NOT allow the laser light to pass into the user's eyes or to reach the camera. Once the position and angle of the pgFocus beam is coincident with that of the TIRF beam a strong return pgFocus beam will be seen that moves with changes in microscope focus. The pgFocus detector array can now be aligned and centered on the beam.
 +
 
 +
== Performance ==
 +
 
 +
pgFocus is designed to track and control focus within ±3nM at 30Hz under optimal conditions (tested with a high NA 60X Objective plus 1.6X optivar).
 +
 
 +
Movie, [[Media:pgFocus.mov]] , of pgFocus in action. 200nM beads were TIRF imaged with uManager's burst mode with a 60X objective with a 1.6X optivar.
 +
 
 +
The microscope is enclosed in an environmental chamber. The doors to the chamber were opened at image 300 and closed at image 600. You will see a disturbance to the focus at both times, but focus is soon corrected within moments. The focus is disturbed due to the change in the temperature gradient across the microscope.
 +
 
 +
[[Media:pgFocus_graph.png]]
 +
 
  
 +
== Thanks ==
  
Movie, [[Media:pgFocus.mov]], of pgFocus in action. 200nM beads were TIRF imaged in burst mode with a 60X objective with a 1.6X optivar.  
+
pgFocus couldn't have been designed without the support of the Open Hardware community.
  
The microscope is enclosed in an environmental chamber. The doors to the chamber were opened at image 300 and closed at image 600. You will see a disturbance to the focus at both times, but focus is soon corrected within moments.
+
[http://www.adafruit.com/ Adafruit industries]
 +
[http://www.sparkfun.com/ Sparkfun Electronics]
 +
[http://www.arduino.cc/ Arduino]

Revision as of 11:54, 20 February 2013

Description

pgFocus is an open source and open hardware focus stabilization device developed by Karl Bellvé at the Biomedical Imaging Group (PMM, University of Massachusetts Medical School).

The pg in pgFocus is short for "Pretty Good". pgFocus isn't "Perfect", or "Definite" but it is pretty good!

Hardware

pgFocus uses the same Atmel ATMEGA 32U4 seen in the Arduino Leonardo.

Software

After the Leonardo was released, pgFocus was redesigned to take advantage of the bootloader for the Arduino Leonardo. If you can write an Arduino sketch, you can modify the source code to pgFocus!


Optics

pgFocus uses a laser beam that is total internally reflected off the cover glass/water interface to monitor the microscope focus. Hence, an objective with an NA of at least 1.45 is required. The laser beam wavelength should be different from that being used for science (808nm is a good choice) and must be coaligned with the TIRF beam. This can be done using a mirror, beam splitter and a short pass filter. Care must be taken to ensure that the fluorescence filter cube and other microscope optics will allow the return of the pgFocus beam back along its input path and back to the pgFocus detector and that the microscope optics will NOT allow the laser light to pass into the user's eyes or to reach the camera. Once the position and angle of the pgFocus beam is coincident with that of the TIRF beam a strong return pgFocus beam will be seen that moves with changes in microscope focus. The pgFocus detector array can now be aligned and centered on the beam.

Performance

pgFocus is designed to track and control focus within ±3nM at 30Hz under optimal conditions (tested with a high NA 60X Objective plus 1.6X optivar).

Movie, Media:pgFocus.mov , of pgFocus in action. 200nM beads were TIRF imaged with uManager's burst mode with a 60X objective with a 1.6X optivar.

The microscope is enclosed in an environmental chamber. The doors to the chamber were opened at image 300 and closed at image 600. You will see a disturbance to the focus at both times, but focus is soon corrected within moments. The focus is disturbed due to the change in the temperature gradient across the microscope.

Media:pgFocus_graph.png


Thanks

pgFocus couldn't have been designed without the support of the Open Hardware community.

Adafruit industries Sparkfun Electronics Arduino

© Micro-Manager : Vale Lab, UCSF 2006-2011 | All Rights Reserved | Contact